Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
They are making a few great observations on the subject of How to Install a Bathtub as a whole in the article in the next paragraphs.
Mounting a bathtub isn't exactly rocket science, but it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough project. If the old bathtub is conveniently available, the task can move speedily; if you need to open a wall surface to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified yourself for the work and fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is better to think about using one before you start. Chances are you might need a specialist plumber to make tube connections.
This post will assist you install a brand-new bath tub in your restroom if you have currently bought a brand-new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices as well as product checklist must consist of the following:
Preparing for the Installment
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been made use of at the very least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washers are in location in between the tap and also the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our topic on Installing A Bathtub. Thanks for spending some time to read our blog post. Enjoyed reading our content? Please share it. Help somebody else discover it. I am grateful for your time. Please check our website back soon.
Visit Site Report this page